Directional Control Valves Ⅰ;

Features

LS-G02 is a solenoid valve with low-wattage type coil (DC:5W or AC:12W). Low current requirement for the valve allow it to be driven directly from a programmable sequence controller.

• Electronic Catalogs   ( 880 KB)

• Cross-sectional views and seal parts   ( 240 KB)

• CompatibilityTable   ( 225 KB)

Features

LS-G03 is a solenoid valve with low-wattage type coil (DC:5W or AC:12W). Low current requirement for the valve allow it to be driven directly from a programmable sequence controller.

• Electronic Catalogs   ( 659 KB)

• Cross-sectional views and seal parts   ( 429 KB)

Features

Realize high-pressure large-flow-rate control at 35 MPa and 100 L (G02) or 160 L/min (G03). Best suited to integration into European Safety Standard (CE) compliant equipment because of dust-/water-proof properties that satisfy the IEC Pub529 IP65 ingress protection grade.

• Electronic Catalogs   ( 1759 KB)

• Cross-sectional views and seal parts   ( 225 KB)

• CompatibilityTable   ( 225 KB)

Features

The capability to switch the valve with a minute signal current (approximately 10 mA) enables direct drive from a programmable sequence controller.

• Electronic Catalogs   ( 377 KB)

Features

Adoption of the shockless spool enables smooth reversal and stopping of the load. Best suited to integration into European Safety Standard (CE) compliant equipment because of dust-/water-proof properties that satisfy the IEC Pub529 IP65 ingress protection grade.

• Electronic Catalogs   ( 645 KB)

• Cross-sectional views and seal parts   ( 189 KB)

Features

Realize high-pressure large-flow-rate control at 35 MPa {350 kgf/cm2} and 300 L/min. Best suited to integration into European Safety Standard (CE) compliant equipment because of dust-/water-proof properties that satisfy the IEC Pub529 IP65 ingress protection grade. Models equipped with a built-in check valve for pilot pressure are also available.

• Electronic Catalogs   ( 1426 KB)

• Cross-sectional views and seal parts   ( 198 KB)

Features

Realize high-pressure large-flow-rate control at 35 MPa {350 kgf/cm2} and 700 L/min.

• Electronic Catalogs   ( 553 KB)

Features

Realize high-pressure large-flow-rate control at 35 MPa {350 kgf/cm2} and 1100 L/min.

• Electronic Catalogs   ( 519 KB)

Features

The highly reliable KSO－G02 adopted as the pilot valve ensures long service life and stable operation. Best suited to integration into European Safety Standard (CE) compliant equipment because of dust-/water-proof properties that satisfy the IEC Pub529 IP65 ingress protection grade.

• Electronic Catalogs   ( 689 KB)

• Cross-sectional views and seal parts   ( 159 KB)

• CompatibilityTable   ( 225 KB)

Features

Using these valves in combination with a pressure compensation valve (MUV, MDM) achieves flow rate characteristics with pressure compensation according to the adjustment made with the flow rate adjusting screw.

• Electronic Catalogs   ( 622 KB)

• Cross-sectional views and seal parts   ( 140 KB)

Features

JP valve enables switching of the direction of flow of the fluid by operating the spool with the hydraulic pilot valve.

• Electronic Catalogs   ( 641 KB)

• Cross-sectional views and seal parts   ( 302 KB)

Features

No hydraulic locking occurs even during long periods of pressurized operation.

• Electronic Catalogs   ( 474 KB)

• Cross-sectional views and seal parts   ( 259 KB)

Features

Explosion-proof solenoid operated valve with a terminal box which have a special structure that essentially internally isolates ignition sources, such as those at electrical connections, so that if explosive gases enter from the outside and ignite and explode inside, they will not adversely affect the outside.

• Electronic Catalogs   ( 619 KB)

• Cross-sectional views and seal parts   ( 169 KB)

Features

DM04 valve enables switching of the direction of flow of the fluid by operating the spool with the manual operation lever. The handle can be operated easily even at a high pressure.

• Electronic Catalogs   ( 537 KB)

• Cross-sectional views and seal parts   ( 255 KB)

Features

JM valve enables switching of the direction of flow of the fluid by operating the spool with the manual operation lever. Enables construction of a wide variety of circuits in combination with 02 size stack valves.

• Electronic Catalogs   ( 452 KB)

• Cross-sectional views and seal parts   ( 322 KB)

Features

Compact directional control valves using a rotary spool available in two models, one dedicated to manual operation and the other with a dog for cam operation (manual operation also possible). The structure has a high level of pressure balance, which suppresses the variation in the force required to operate the handle according to the pressure change.

• Electronic Catalogs   ( 434 KB)

• Cross-sectional views and seal parts   ( 331 KB)

Features

Enables acceleration/deceleration of a cylinder by adjusting the plunger stroke with a cam mechanism.

• Electronic Catalogs   ( 414 KB)

• Cross-sectional views and seal parts   ( 243 KB)

Features

DD2 is a 2-position, 2-way valve which enables switching of the fluid passage in a hydraulic pilot circuit or interlocking circuit using cam operation. Compact and lightweight designs are ideal for automatic operation.

• Electronic Catalogs   ( 427 KB)

• Cross-sectional views and seal parts   ( 291 KB)